The LandSco^® Light Inspection System

The LandSco^® Light detects surface defects before your print job becomes scrap. By producing a very wide and very shallow beam of light, the LandSco Light can carefully control the illumination of the surface to be inspected. The viewer can quickly and clearly see, for example, powder smaller than 20 microns without the aid of magnifiers.

Contaminants on the surface (spray powder, lint, etc.) are highlighted brilliantly on the side facing the light, and cast a deep shadow on the opposite side. Scratches, picks, calendar pits, etc., create deep shadows with the side opposite the light catching the light and being highlighted.

All are built so that the lamps can be replaced in the field. The Model G and GA have adjustable legs to facilitate alignment procedures.

Standard Series

Model G

Used for on-machine inspection, or mounted on an inspection table for off-machine inspection. The size of the surface to be inspected can be from 42-48" wide by 200" deep. Controls for dimming and on/off operation are located on the back of the cabinet.

Model GA

Includes remote control with a 12-foot cable for dimming and on/off operation. Features and dimensions same as Model G

Model Mini

This compact, portable version of the Model G, can be placed on the same surface as the sample to be inspected or even on the sample itself. Its portability makes the Mini especially useful for examining roll ends, skid load edges, etc., where it is easier to take the light to the sample than to take the sample to the light.

Model MS

Model MS is basically a Model GA acting as a master control unit for any number of slave units attached electronically so that all units operate simultaneously. The slaves operate just like the master, except that they cannot operate independently. The unit was designed for continuous on-line inspection for very wide running webs, or for off-line inspection of exceedingly large samples, such as 4x16 foot panels. It offers all the advantages of the Model GA, plus the advantage of being able to illuminate much larger surfaces.

The "New" High Intensity Series Inspection Lights

Features include:

• 40% brighter than standard series
• Can effectively be used in lighted environments
• Wider effective viewing areas
• Taller beam height (for viewing thicker samples)
• Easy access to lamps for replacement (2 minutes or less) or quick change lamps

Model H or HA (Long Throw Light)

Can be used for on-machine inspection or can be mounted to an inspection table for off-machine inspection or table top use. Both models can illuminate surfaces 22" – 96" wide up to 140" deep.

Can be used by any manufacturer who needs to detect surface defects. These markets include printing, converting, paper manufacturing, corrugated, flooring, carpet manufacturing and gypsum board or any manufacturer looking for surface defects.

Inspection Table Light (ITL)

The ITL (short throw light) is a unit designed to turn a flat, level surface into an inspection area of sizable proportions. It can also be placed along side a moving web to create an on-line inspection light. This model can illuminate surfaces from 40" wide within 3" from the light to 96" wide just 48" from the light, with an effective depth view of 60". All operating controls are located on the side of the unit for operator convenience.

Can be used by any manufacturer who needs to detect surface defects. These markets include printing, converting, paper manufacturing, corrugated, flooring, carpet manufacturing and gypsum board or any manufacturer looking for surface defects.

Model Super H (Long Throw Light)

This wider version of the model H is just 30" wide but offers twice the viewing area of the smaller unit. It is designed for large format viewing in the manufacturing of flooring, carpeting, Gypsum board, and door manufacturing or anywhere a large sample requires inspection. The H-Super or Super H located as close as 24" from sample can illuminate a 65" wide area to over 216" wide at 200" plus deep.

Inspection Tables

Doyle Systems offers a line of standard and custom-manufactured quality control inspection tables. This line also incorporates our extensive line of "LandSco" Surface Inspection Lighting for a wide variety of application requirements. This lighting is designed to view surfaces of samples in their entirety, from 28" x 40" up to 46" x 240" and is multi-directional.

Can be used by any manufacturer who needs to detect surface defects. These markets include printing, converting, paper manufacturing, corrugated, or any manufacturer looking for surface defects.

Tectonic Video Inspection Systems

Provide high-speed, video inspection on press to ensure that optimal print quality is maintained. They deliver superior picture quality based on flicker-free full-frame technology and CCD cameras with a high scan rate. The line includes everything from simple firmware-based manual systems to completely motorized and programmable systems.

With these systems, printers can monitor anything from basic registration to an automated inspection system with active feedback including color, bar codes, repeat length and pharmaceutical codes.